I have this topic here because some of Aerospace control modules are built by using NI LabView . It's a simple GUI programming language.
Front panel - User interface panel.
Block diagram - Contains graphical source code.
You can try to make your own program from the basics, like adding two numbers, etc. You will love it.
Example:
I have built a model to control temperature and pressure levels in a Tank (can be fuel tank), the system LED will blink if the levels are higher than the recommended. Blinking of LED is controlled by Boolean conditions.
Temperature ==> Ranges between 20-300 degree Celsius
Pressure ==> ranges between 0-20 MPa
Condition:
LED for Temperature will blink if the value is above 200C
LED for Pressure will blink if the value is above 10MPa
LED will remain GREEN if the levels are below the critical values.
LabView has loop as well, but WHILE loop is used and "Iteration" shows how many times the loop has run.
Front panel:
Block diagram: Source code
-
- Active Topics
-
-
- by Eli 2 days ago Re: What is in Your Mind? View the latest post Replies 703 Views 301847
- by Eli 2 days ago Russia Invades Ukraine View the latest post Replies 663 Views 236885
- by Eli 3 days ago All in One: YouTube, TED, X, Facebook and Instagram Reels, Videos, Images and Text Posts View the latest post Replies 326 Views 36195
- by Eli 5 days ago PySpark for Large Data Processing View the latest post Replies 1 Views 7841
- by Eli 1 week ago President Museveni's Speech During International Development Association (IDA) Summit View the latest post Replies 1 Views 305
- by Eli 1 week ago From Simple Linear Regression Analysis to Covariance & Correlation to Independent Determinant, and R-Squared View the latest post Replies 11 Views 24908
- by Eli 1 week ago Collection of Greatest Christian Hymns of all Times View the latest post Replies 34 Views 69018
- by Eli 2 weeks ago Pondering Big Cosmology Questions Through Lectures and Dialogues View the latest post Replies 34 Views 58217
- by Eli 2 weeks ago Programmatically Manipulate Files: Renaming, Reading, Writing, Deleting, and Moving Files Between Folders View the latest post Replies 7 Views 17256
- by Eli 2 weeks ago Iran Launches Retaliatory Attack Against Israel, and Israel Retaliates by Attacking Iranian Isfahan Millitary Base View the latest post Replies 28 Views 19563
-
Modeling simple SCADA system using LabView
-
- Expert Member
- Reactions: 23
- Posts: 55
- Joined: 7 years ago
- Has thanked: 14 times
- Been thanked: 28 times
- Contact:
- Attachments
-
- simulation1.gif
- (11.17 MiB) Not downloaded yet
- simulation1.gif
- (11.17 MiB) Not downloaded yet
-
- Capture.PNG
- (21.03 KiB) Not downloaded yet
- Capture.PNG
- (21.03 KiB) Not downloaded yet
0
Last edited by Joseph Bundala on Sun Jun 25, 2017 1:53 pm, edited 2 times in total.
-
- Expert Member
- Reactions: 23
- Posts: 55
- Joined: 7 years ago
- Has thanked: 14 times
- Been thanked: 28 times
- Contact:
Exactly, example in case of higher temperature then PLC will start a fan, cooling gas, or any means set for cooling the system.
SCADA<==>PLC<==>ACTUATORS
Actuators are physical phenomenons like motors, etc.@gaDgeT
SCADA<==>PLC<==>ACTUATORS
Actuators are physical phenomenons like motors, etc.@gaDgeT
0
-
- Information
-
Who is online
Users browsing this forum: No registered users and 0 guests